日韩国品一二三产品区别,妺妺窝人体色www婷婷

站內搜索

新聞資訊

公司新聞行業動態

熱點

自動上料平口攪拌機多種方量可供選擇

2022-12-23

混凝土自動上料攪拌車的功能有哪些？

2022-12-19

混凝土自動拌料車移動式可自行走戶外施工

2022-12-16

自上料攪拌車企業這么多，買車的時候應該看哪方面？

2022-12-12

關于山汽

聯系人：劉老師

電話：400-879-1999

公司：山東山汽工程機械（集團）有限公司

地址：山東省萊州市206國道與308省道交叉口東南50米

自動攪拌一體車轉向沉重的原因有哪些？

所屬分類：行業動態 發布時間：2022-02-25 來源：http://www.842233.cn/ 瀏覽量：0

自動攪拌一體車在其使用周期內隨著壽命的而不斷流逝會逐漸轉向沉重，這時我們可采用排除法來檢查它的問題，以及導致自動攪拌一體車轉向沉重故障現象的常見原因：

During its service life, the automatic mixer truck will gradually turn heavy with the passage of its service life. At this time, we can use the troubleshooting method to check its problems and the common causes of the heavy turning fault of the automatic mixer truck:

1、，自動攪拌一體車在停機熄火時用壓力表檢查自動攪拌一體車先導壓力值，正常的先導壓力值應該是發念頭怠速的時候不低于2.2MPA,高速的時候要不高于5MPA,假如檢查自動攪拌一體車壓力值不為劃定的值，那么導致自動攪拌一體車轉向沉重故障現象泛起的原因就是先到壓力值分歧錯誤，就要調整。自動攪拌一體車先導壓力值的調整方法是：，先用的拆卸工具松開溢流閥鎖緊螺母，然后假如是先導壓力值偏小，就向順時針方法調大先導壓力值，假如是壓力值偏小，就向逆時針方法調小。調整先導壓力值后，自動攪拌一體車轉向沉重故障排除。

1. First of all, check the pilot pressure value of the integrated automatic mixer with a pressure gauge when the integrated automatic mixer is shut down. The normal pilot pressure value should be no less than 2.2MPa at idle speed and no more than 5MPa at high speed. If the pressure value of the integrated automatic mixer is not the specified value, Then the reason for the heavy steering fault of the automatic mixer is that the pressure value is wrong first, so it needs to be adjusted. The adjustment method of the pilot pressure value of the automatic mixer is as follows: first, loosen the lock nut of the overflow valve with a professional disassembly tool, and then if the pilot pressure value is too small, increase the pilot pressure value clockwise. If the pressure value is too small, reduce it counterclockwise. After adjusting the pilot pressure value, the heavy steering fault of the automatic mixer is eliminated.

2、假如先導壓力值正常，那么就繼承檢查自動攪拌一體車的管路連接，查看有沒有有沒有泄漏，管路接頭有沒有梗阻，自動攪拌一體車液壓缸有沒有內漏等問題。自動攪拌一體車先導壓力值的調整方法是：，先用的拆卸工具松開溢流閥鎖緊螺母，然后假如是先導壓力值偏小，就向順時針方法調大先導壓力值，假如是壓力值偏小，就向逆時針方法調小。調整先導壓力值后，自動攪拌一體車轉向沉重故障排除。

2. If the pilot pressure value is normal, continue to check the pipeline connection of the automatic mixing vehicle to see whether there is leakage, whether the pipeline joint is blocked, and whether the hydraulic cylinder of the automatic mixing vehicle has internal leakage. The adjustment method of the pilot pressure value of the automatic mixing integrated vehicle is: first, loosen the lock nut of the overflow valve with a professional disassembly tool, and then if the pilot pressure value is too small, increase the pilot pressure value clockwise. If the pressure value is too small, reduce it counterclockwise. After adjusting the pilot pressure value, the heavy steering fault of the automatic mixer is eliminated.

3、液壓缸內漏，導致泛起自動攪拌一體車轉向沉重故障。

3. The hydraulic cylinder leaks, resulting in the heavy steering fault of the automatic mixer.

4、自動攪拌一體車油路有可能進了空氣。

4. There may be air in the oil circuit of the automatic mixer.

5、管路連接錯誤或者是管路有梗阻，導致自動攪拌一體車轉向沉重故障現象。

5. The pipeline connection is wrong or the pipeline is blocked, resulting in the heavy steering fault of the automatic mixer.

6、自動攪拌一體車轉向系統壓力過低。

6. The steering system pressure of the automatic mixer is too low.

7、自動攪拌一體車先導系統出現故障。

7. The pilot system of the automatic mixer truck failed.

以上就是今天帶給大家的知識，自動攪拌一體車專注行業多年，為用戶不斷的提供有價值的內容，更多內容請繼續關注我們：http://www.842233.cn/

The above is the knowledge brought to you today. The automatic mixer has been focused on the industry for many years and continuously provides users with valuable content. Please continue to pay attention to us for more content: http://www.842233.cn/

上一頁：如何節省自動上料車的成本？下一頁：功能齊全的自動攪拌一體機是怎樣工作的

熱門產品 / HOT PRODUCT