欧美人与动牲交a精品,国产精品一区12p,久久嫩草精品久久久久精品

站內搜索

新聞資訊

公司新聞行業動態

熱點

自動上料平口攪拌機多種方量可供選擇

2022-12-23

混凝土自動上料攪拌車的功能有哪些？

2022-12-19

混凝土自動拌料車移動式可自行走戶外施工

2022-12-16

自上料攪拌車企業這么多，買車的時候應該看哪方面？

2022-12-12

關于山汽

聯系人：劉老師

電話：400-879-1999

公司：山東山汽工程機械（集團）有限公司

地址：山東省萊州市206國道與308省道交叉口東南50米

自動攪拌一體車轉向沉重的原因是什么？

所屬分類：公司新聞發布時間：2021-05-26 來源：http://www.842233.cn/ 瀏覽量：0

自動攪拌一體車在其使用周期內隨著壽命的而不斷流逝會逐漸轉向沉重，這時我們可采用排除法來檢查它的問題，以及導致自動攪拌一體車轉向沉重故障現象的常見原因：

During its service life, the automatic mixer truck will gradually turn heavy with the passing of its life. At this time, we can use the elimination method to check its problems and the common causes of the heavy turning fault of the automatic mixer truck

1、，攪拌車在停機熄火時用壓力表檢查自動攪拌一體車先導壓力值，正常的先導壓力值應該是發念頭怠速的時候不低于2.2MPA,高速的時候要不高于5MPA,假如檢查自動上料攪拌車壓力值不為劃定的值，那么導致自攪拌車轉向沉重故障現象泛起的原因就是先到壓力值分歧錯誤，就要調整。

1. First of all, when the mixer is shut down, check the pilot pressure value of the automatic mixer with a pressure gauge. The normal pilot pressure value should be no less than 2.2MPa at idle speed and no more than 5MPa at high speed, Then, the cause of heavy steering fault of self mixing truck is that the difference of first arrival pressure value is wrong, so it needs to be adjusted.

2、假如先導壓力值正常，那么就繼承檢查攪拌車的管路連接，查看有沒有有沒有泄漏，管路接頭有沒有梗阻，攪拌車液壓缸有沒有內漏等問題。

2. If the pilot pressure value is normal, then continue to check the pipeline connection of the mixer, check whether there is leakage, whether the pipeline joint is blocked, whether the hydraulic cylinder of the mixer has internal leakage and other problems.

3、液壓缸內漏，導致泛起自動攪拌一體車轉向沉重故障。

3. The leakage in the hydraulic cylinder caused the heavy steering fault of the automatic mixer truck.

4、攪拌車油路有可能進了空氣。

4. There may be air in the oil circuit of the mixer.

5、管路連接錯誤或者是管路有梗阻，導致自動攪拌一體車轉向沉重故障現象。

5. Pipeline connection error or pipeline obstruction, leading to the automatic mixer truck steering heavy fault phenomenon.

6、攪拌車轉向系統壓力過低。

6. The steering system pressure of mixer is too low.

7、攪拌車先導系統出現故障。針方法調小。調整先導壓力值后，自動攪拌一體車轉向沉重故障排除。

7. There is a fault in the pilot system of the mixer. The needle method is adjusted smaller. After adjusting the pilot pressure value, the heavy steering fault of the automatic mixer truck was eliminated.

上一頁：自動攪拌一體機耐磨配件為什么會損壞? 下一頁：如何清理自動攪拌一體車散熱器？

熱門產品 / HOT PRODUCT